12 Tips to Start Ground Rod Installation/Testing Business

Ground Rod Installation/Testing Business: A ground rod is an important part of an electrical system. It allows uncontrolled electricity to go to the ground instead of causing a fire or damaging a building. When installing a ground rod, you need to make sure that electricity will easily flow through it into the earth. The resistance to the flow of electricity is measured by a ground meter and is read in ohms. The lower the number of ohms of resistance a grounding system has, the better your protection is.

Ground Rod Installation/Testing Business:: BusinessHAB.com

A winner never stops trying. It’s not an experiment if you know it’s going to work. You can request publication of your article for publication by sending it to us via our Email below. businesshabblog@gmail.com or SMS/WhatsApp) or call +2347034920650.  Click here to start business now with businesshab.com
businesshabblog@gmail.com

Read also: Top 19 Healthily Feeding Tips in Nigerian Restaurant

Ground Rod Installation/Testing Business

1.Get a clamp-on ground meter.

 A clamp-on ground meter is a specialized electronic machine that checks electrical resistance.
These meters can range from about $100 (USD) to over $1500 for professional models.

They are available at hardware stores, home improvement stores, and online retailers of electrical supplies.

  • The clamp-on meter will give you a reading in “ohms,” which is the unit of measurement for resistance. It may be signified with the symbol “Ω” on the meter.

See also: 29 Best E- Learning Resources for Kids in Nigeria

Ground Rod Installation/Testing Business

2. Clamp the meter on the ground rod or grounding electrode conductor.

Open the clamp by pressing the lever on the side of the meter and holding it down. Then put the clamp around the grounding electrode conductor or the top of the ground rod. Let the clamp close by letting go of the lever.

  • The meter should be used as close to the ground rod as possible. Using it further down the electrical system, such as near the electrical panel, will read other ground sources in addition to the ground rod.

See also:21 Best way to open Fleet Business

Ground Rod Installation/Testing Business

3. Turn on the meter.

How you start the meter depends on the specific brand you have. Some simply have a button that says “power” or “on.” Others have a dial that needs to be set to ohms.

  • If you are unsure of how to turn on your ground meter, follow the directions included with it.

Read also:  22 Best way to Hire a Divorce Lawyer 

Ground Rod Installation/Testing Business

4. Assess the readings on the meter.

Your clamp-on ground tester will have a screen that will show you a numeric reading.

The lower the number on the meter, the better your grounding rod is working. In general, a reading under 25 ohms means that your ground rod has a good connection to the earth.

Ground Rod Installation/Testing Business

5. Get an earth electrode tester.

This is an older type of resistance meter that uses multiple ground probes and wires to assess a ground rod’s resistance. This type of tester is usually available at hardware and home improvement stores, as well as from online retailers.

  • Using an earth electrode tester instead of a clamp-on tester will take a lot more time and effort. If you have the option of using a clamp-on meter instead, do it.

See also: 19 Best ways to Get Money Without Working during lockdown 

Ground Rod Installation/Testing Business

6. Insert 2 ground probes into the ground.

The ground probes need to be inserted into the ground at specific distances away from the ground rod. The furthest ground probe needs to be at a distance that is 10 times the length of the ground rod. For instance, if the ground rod is 8 feet (2.4 m) long, the furthest probe should be 80 feet (24 m) away. The second ground rod should be located halfway between the furthest probe and the ground rod.

  • The ground probes are typically about 1 foot (0.30 m) long. They should be inserted into the ground until the top of them is just visible.
  • The leads that come with earth electrode testers are typically very long, so they should reach the required distance.

    Ground Rod Installation/Testing Business

7. Connect all three leads.

The three leads your meter comes with should be inserted into the openings on the meter. Then, the other end of 1 of the leads needs to be connected to the top of the ground rod. The other 2 each need to be connected to one of the ground probes.

  • In general, it doesn’t matter which lead goes to which ground rod or probe. However, the lead for the furthest ground probe should be the longest one so that it will reach.

Read also: 61 Best way to Invest in Stocks

Ground Rod Installation/Testing Business

8. Turn on the meter and take a reading.

How you turn on the meter depends on the specific type of meter you have. Most have a dial that should be set to the ohm symbol or to a mark that says “3 pole,” which is referencing your 3 points of contact with the earth. Once the meter is on, read what the screen says.

  • If a ground rod has a good connection to ground, its reading should be a number below 25.

See also: 31 Tips to Start Mobile Accessories Retail Business in Cameroon

Ground Rod Installation/Testing Business

9. Verify your original reading.

Move one of your probes to a location 2 feet (0.61 m) closer to the ground rod. Take a reading of the resistance once again. Then move that same probe so it is 2 feet (0.61 m) closer to the second probe than it was originally. Take another reading. All the readings that you get should be very similar.

  • To ensure that your ground rod is sufficient, the average of all 3 readings should be less than 25 ohms.

Read on:31 Tips to Start Watches & Sunglasses Retail Business in Cameroon

Ground Rod Installation/Testing Business

10. Make sure the grounding system connections are secure.

If you don’t get a satisfactory ground reading, check your grounding system for problems. Make sure the clamp that connects the ground rod and the grounding circuit conductor is very tight. Also ensure that the ground electrode conductor is solidly connected to the grounding bar in the electrical panel.

  • Most electrical systems also have secondary grounding means, such as the grounding bar being connected to a cold water pipe that goes into the ground. Make sure that the secondary grounding means is also securely connected.

Read also: 31 Tips to Open Men’s/Women’s Fashions Retail Business in Cameroon

Ground Rod Installation/Testing Business

11. Install a new ground rod in a different location.

In some instances, ground rods can be installed in areas where the earth has a lot of resistance. For instance, if a ground rod is driven into a very rocky and dry area it may not conduct electricity into the ground well. If this is the case for your ground rod, the best solution is to drive a different rod into a different location.

  • This may not require you to put a ground rod a long distance away from the original rod. Even a few feet can make a difference for the ground resistance.

Read on: 31 Tips to Start Health/Well-being Retail Business in Cameroon

Ground Rod Installation/Testing Business

12. Install a second ground rod.

If you have too much resistance in your initial ground rod, you can connect a second one in series to reduce the overall resistance. This will ensure that any ground fault will be able to go to ground easily.

  • Your second ground rod should be located at a distance that is equal to the length of your ground rod. For example, if your first ground rod is 8 feet (2.4 m) long, your second ground rod should be located 8 feet (2.4 m) from the first ground rod.

3 comments
  1. We offer you the opportunity to advertise your products and services.
    Hello! There is a good offers for you. I want to offer the possibility of sending your commercial offers or messages through feedback forms. The advantage of this method is that the messages sent through the feedback forms are included in the white list. This method increases the chance that your message will be read. Mailing is made in the same way as you received this message.

    Sending via Feedback Forms to any domain zones of the world. (more than 1000 domain zones.).
    The cost of sending 1 million messages for any domain zone of the world is $ 49 instead of $ 99.
    Domain zone .com – (12 million messages sent) – $399 instead of $699
    All domain zones in Europe- (8 million messages sent) – $ 299 instead of $599
    All sites in the world (25 million messages sent) – $499 instead of $999
    Domain zone .de – (2 million messages sent) – $99 instead of $199
    Domain zone .uk – (1.5 million messages sent) – $69 instead of $139
    Domain zone .nl – (700 000 sent messages) – $39 instead of $79

    Discounts are valid until March 25.

    In the process of sending messages, we do not violate the rules of GDRP.
    This message is created automatically use our contacts for communication.

    Contact us.
    Telegram – @FeedbackFormEU
    Skype – FeedbackForm2019
    Email – FeedbackForm2019@gmail.com

    All the best

Leave a Reply

Your email address will not be published. Required fields are marked *

You May Also Like