Learning links alshaya: How to remove watch band links
Learning links alshaya: When you find the perfect watch, it’s important that it fits you perfectly. Sometimes, it will be necessary to remove links from the watch band in order to get an exact fit. Read the following article to learn how to remove watch band links in order to tailor any watch to the specifications of your wrist.
Measure the watch band. Before you set about removing any watch links, it is necessary to measure your watch band so you know exactly how many links you will need to remove. To do this:
- Position the watch on your wrist exactly the way you intend to wear it. When you are satisfied with the way it is positioned, turn your wrist over so that the watch band clasp side is facing up.
- With the watch band on your wrist, gather the slack in the band and hold the links together to simulate them being removed. Stop gathering the links up when the watch band fits your wrist just the way you like.
- Look where the links are gathered close together at your wrist – be aware that because of the design of the watch band they may not touch. The loose hanging links will tell you the number of links you should remove first.
- If you can’t accurately judge the number of links to remove, remove one less than you expect – it is always easier to remove another link than add one back in.
- Be aware that it is always better to remove an even number of watch links.This way, you can remove the same number of links from each side and ensure that the clasp is still located in the center of the watch strap.
Learning links alshaya
Gather your tools. In order to remove watch links properly, you will need certain tools. These may include:
- A thin, pointy object like a spring-bar removal tool or pin pusher.
- A long-nosed pliers.
- A small hammer.
- A screwdriver.
- A parts tray.
Prepare your work area. Make sure that your work area is free from clutter. It is probably a good idea to put down a sheet or some other covering on your work surface and possibly the floor. This is to make sure that any small pieces won’t get lost.
Separate the bracelet. With some metal watch straps, it is necessary to separate the bracelet before you can remove any links. To do this:
- Remove the spring bar from the watch strap clasp. To identify which spring bar it is, hold the clasp in your left hand, and it will be the one on the left side.
- Use the spring bar removal tool or pin pusher to compress the spring bar and lever it out of the clasp.
- Be careful that it doesn’t spring across the room, because this is the only one you have!
Learning links alshaya
- You should be able to push the pin 2 or 3mm and then pull it out from the other side using your pair of pliers or by hand.
- Place the pin in your parts tray, you will need it to put the bracelet back together again.
Watch out for a small metal ferrule. Some watch bands contain small metal ferrules in the middle of joining links that will be released when you take out a pin. It may fall onto the floor or work station, so keep an eye out for it. You will need it later.
Learning links alshaya
Remove the link’s second pin. Repeat the pin removal process on the link’s other pin. When you have finished, you should have two pins and possibly two ferrules ready to use later.
Remove the next link. If you need to, remove another link on the other side of the clasp, using the same process. When you have removed as many links as you need to, you are ready to join the bracelet back together.
Reassemble the watch band. Once the required links have been removed the pin will need to replaced into the band to complete it again. To do this replace the pin in the opposite direction to the arrows.
- If your watch band has ferrules, place the ferrule in the middle of the link that you are joining up, and when you push the pin back into the hole, make sure to engage the ferrule.
- If you need to, you can gently tap the pin back into place using your small hammer.
Learning links alshaya
- If it is a little loose or a little tight, it may be possible to further adjust the bracelet by inserting the clasp’s spring bars into an alternative set of holes to adjust the size.
- Make sure to keep any extra links and spare pins or ferrules safe, you may need to use them again in the future.
- Continue to turn in a counterclockwise motion until the screw becomes loose.
- Use a pair of tweezers or pliers to grab the screw before it falls. Make sure to keep it somewhere safe, as you will need it to reassemble the watch.
- Ensure that you do this over a table or tray to make sure you don’t lose screws should they fall during the process.
Learning links alshaya
Learning links alshaya
Learning links alshaya
Learning links alshaya
Tips
-
If you’re having trouble seeing when you remove watch links, use a mounted magnifying glass to enhance the pins, links, and other small watch parts.
-
After sizing, have fewer links on the 6 o’clock side of the bracelet (the links under the 6). In general, this makes the deployment clasp more balanced when wearing.
Learning links alshaya
Conclusion
Learning links alshaya
Things You’ll Need
Spring bar removing tool, or pin pusher
1mm screwdriver
Needle nose pliers (smooth jawed)
A small hammer
A parts tray
Flexible tape measure
Magnifying glass (optional)