How do you blend a fade haircut?

Haircuts for men: The fade haircut is a popular, flattering style where the hair is cut short near the temples and neck and gradually gets longer near the top of the head. Depending on the hair and personal style, fades can be high and trimmed or start lower and blend into the neckline. Even if you’ve never faded hair before, cutting this style is simple as long as you have the right tools.

Do you have any well-written article you would like to publish on BusinessHab? You can request publication of your article for publication by sending it to us via our Email below. Do You Have any information to share with us? Do well to contact us on Email below.

Try a low fade on hair with more texture. If your client’s hair is thick or wavy, buzz the hair with the shortest clipper guard settings at a lower area, preferably below the ears and around the nape of the neck. Low fades show off a hair’s texture better and work with the hair’s natural pattern.

  • The longer the hair is on top, the lower the fade should be.

Choose a high fade for more contrast. If you want a cleaner, more buzzed style on the back and sides, go with the lowest clipper guard settings moving up to the temples. Try a high fade for a sleeker look.

  • High fades work well with square or round face shapes because they lengthen the appearance of the face.

Use a pair of clippers and styling scissors to cut a fade. Choose a pair of clippers with at least 3 guard lengths so you can blend the client’s hair as you go. Use clippers on the back, sides, and nape and styling scissors on the top.

  • If you prefer a softer fade, you can also use styling scissors on the back and sides. However, keep in mind that this is an advanced technique, so do not attempt it unless you are very experienced with fades.
  • Do not use household scissors to trim hair, as it can result in a blunt or uneven cut.
  • Keep in mind that you can use clippers near the top of your head too if you like it shorter than 1 in (2.5 cm).

Haircuts for men

Wash and dry the hair before cutting it. Damp, clean hair is easier to work with while cutting fades. Wash the person’s hair with shampoo, rinse it with water, and air or towel dry it until it is damp.

  • The hair should be somewhat damp, not dripping wet, to make cutting it simpler. The client’s hair should not be so wet that it clumps together or you may end up cutting out chunks of it.

Trim the top with styling scissors. Lift sections of hair from the top of the head so that the tips of the hair protrude from between your forefinger and middle finger. Trim the tips of the hair with the scissors at your desired length.

  • Continue trimming the hair at the top of the head in sections until you’ve trimmed it to the same length.
  • If the person has bangs, trim the bangs in sections for a neat and even line.

    Haircuts for men

Trim the entire sides and back with a long guard size. Set the clippers to a long guard length, depending on how long you want the top of the fade, and buzz the entire back and sides. Continue trimming until each part of the hair is a uniform length.

  • Use a vertical movement to cut the hair starting at the hairline and up towards the top of the client’s head.
  • Work against the grain of the hair to achieve an even cut.
  • Lift the clippers up and outwards slightly at the end of each stroke as you get close to the rounded part of the person’s head to help the cuts fade together smoothly.

Cut the back of the head with the next shortest guard. Switch to the next shortest guard and, beginning in the back, cut the hair in vertical strokes from the neck toward the crown. Stop just below the crown so that the hair on top of the head is left long.

  • If you were using a #3 guard size, for example, switch to a #2.
  • Blend any uneven lines that you notice by going back over them with the clippers.

    Haircuts for men

Buzz the nape with the shortest guard setting. Start at the nape of the neck and cut in upward strokes toward the back of the head’s center. Work your around the head’s back and sides, pulling back at the same height for an even finish.

  • Pull back with your clippers to blend the nape’s short hair with the back’s long hair.
  • Shave the hair from the nape and below to create a clean, neat edge.

Clean the edges with your clippers. Move your clippers on the shortest guard setting along the nape and edges of the sides. If you find any poorly blended or uneven spots while you go, go back over them with the appropriate clipper guard. You should also turn the blade around and use it to go around the edges of the hairline. This will help to create a clean outline.

Haircuts for men

Inspect the fade and brush off any hair clippings. Ask the client to look at their new cut and determine whether they would like a shorter or longer fade. Brush away any cut hair from the neck and collar before you move on to styling the hair

  • If the person wants a shorter cut, trim off small amounts at a time to avoid cutting off too much.

Style the top with a hair styling product. Clay, wax, gel, and pomade all work well with faded hair. Work a small amount of styling product into the top, brushing or combing it as you do so to give it a clean, neat look.

  • Ask the client what products they normally use and, if possible, incorporate these items, so they can replicate the style themselves.

Trim the fade every 4 to 6 weeks, as regular maintenance. To maintain the same hair length and fade, re-trim the cut approximately once every 4 to 6 weeks. Although fades grow out evenly, their style can change significantly as they grow out and require routine trims.

  • Use the same clipper guards and styling method that you did while initially cutting the hair.

Haircuts for men

More tips

  • For an even and well-maintained fade, plan on trimming the cut every 4-6 weeks.

  • Consult the person whose hair you’re cutting as you work to make sure they’re satisfied with the length and overall style.

  • If the person has a cowlick that would make it difficult to fade at a certain point on the head, start the fade just above or below it.

Leave a Reply

Your email address will not be published. Required fields are marked *